Those plugs aren't cheap! - Kawasaki Versys Forum
Register Members List Calendar Search Today's Posts Mark Forums Read Motorcycle EscrowInsurance
Go Back   Kawasaki Versys Forum > Kawasaki Versys Motorcycle Talk > General Kawasaki Versys Discussions

 

General Kawasaki Versys Discussions For discussions on anything and everything related to the Kawasaki Versys.

Reply
 
Thread Tools Display Modes
  #1  
Old 08-26-2012, 04:39 PM
Time's Avatar
Time Time is online now
Member
 
Join Date: Apr 2012
Location: NW Ohio
Posts: 1,069
Default Those plugs aren't cheap!

$15.00 each! OUCH my poor bank account.

Just getting everything together for the 7,500 service and the cost of the plugs were a bit of a shock. And why does Kawasaki say 7,500 on the plug change BUT every two years on the air filter? You have to pull the filter to get the plugs out, right?

Should I clean the factory filter or replace it with another Stock filter element or aftermarket at twice the cost?

Other than that I keep 3qts of sys on hand along with the oil filter and gasket and junk.

Should I pull the swing arm and grease the bearings while I'm at it? If it like the one in my KLR there wasn't enough grease to lube a ant's a$$ in all of them together.

BTW if you use a pit stand and put the tail trunk on your V and then try and jack it up, your going to have a BAD day! Note to self pull box and plate so I don't bash my head in again!
__________________
Or was that look THEN leap?

Last edited by Time; 08-28-2012 at 05:11 PM.
Reply With Quote
Sponsored Links
Advertisement
 
  #2  
Old 08-26-2012, 05:05 PM
Squirreltoe's Avatar
Squirreltoe Squirreltoe is offline
Member
 
Join Date: Jun 2010
Location: Ankeny, IA
Posts: 57
Default

I would not change plugs yet unless you are noticing problems. Mine looked really good yet at 15,000 miles. I didn't touch the filter until 15,000 either and I ride a fair amount of gravel. I posted some pics in another thread.


http://www.kawasakiversys.com/forums...ht=squirreltoe

Good Luck!
Reply With Quote
  #3  
Old 08-26-2012, 07:04 PM
weljo2001's Avatar
weljo2001 weljo2001 is offline
Member
 
Join Date: Jan 2010
Location: Ft.Worth,TX. Norwalk CA
Posts: 9,865
Default

I got my Denso plugs off of amazon.com for less than $10.00 ea.
__________________
2009 Blue Versys. Sold

My Farkles......http://www.kawasakiversys.com/forums...ad.php?t=20013
My Video Channel http://www.youtube.com/user/weljo2001?feature=mhee
My Photos...http://www.flickr.com/photos/54181788@N06/sets/

I'm not a Gynecologist. "But I'll Take A Look"

Everyone has a plan 'till they get punched in the mouth...
Mike Tyson

"Ya'll can go to hell, I'm goin' to Texas!"...Davey Crockett
Reply With Quote
  #4  
Old 08-26-2012, 09:50 PM
GDI GDI is offline
Member
 
Join Date: Oct 2011
Location: Madison, Wisconsin, USA
Posts: 108
Default

I cleaned the stock filter at around 7500 miles (last week). It seemed to me that it had way too much oil on it. It was super-saturated. I re-oiled it (lightly!) and re-installed it before my "trip", and I saw better mileage than I'd seen in the past.

I ran 4 tanks through the V. Mileage was 50mpg, 55mpg, 56mpg, and 51mpg. The first and last tanks had more interstate miles getting to the good riding, and getting home again. . . .

I'm waiting on the sparkplugs 'til 15,000 miles or possibly this winter based on other posts here.

GDI
Reply With Quote
  #5  
Old 08-27-2012, 12:14 AM
Fastoman's Avatar
Fastoman Fastoman is offline
Member
 
2009 Kawasaki Versysy
Join Date: Sep 2009
Location: Ipoh.Perak.Malaysia
Posts: 4,582
Default

I changed the plug for no apparent reason as the original was still good at 30K km and yes Denso plugs are expensive.

After market air filter seem to give good account on mileage than the original filter. Might change to after market, though the original one is still pretty good at 37K KM.
Reply With Quote
  #6  
Old 08-27-2012, 12:23 AM
T Cothron T Cothron is offline
Member
 
2009 Kawasaki Versys
Join Date: May 2010
Location: Lafayette,TN
Posts: 128
Default

The tool kit sparkplug socket Thingy and a14mm wrench will allow removal of the plugs without removing anything else. Standard NGK plugs can be found much cheaper on-line. And they last more than 7500 miles. If you have'nt cleaned the air filter at 7500 miles it's likely due though.
__________________
Lean/Two
Reply With Quote
  #7  
Old 08-27-2012, 03:52 AM
invader's Avatar
invader invader is offline
Member
 
Join Date: Mar 2008
Location: Kapuskasing Ontario Canada
Posts: 5,852
Default

NGK CR9EIA-9 for $6.41 each (search CR9EIA-9): http://www.rockauto.com/catalog/catalog.php

Denso IU27A: http://www.ebay.com/itm/1-New-DENSO-...53ac23&vxp=mtr

Denso IU27: http://www.ebay.com/itm/1-New-DENSO-...4ce508&vxp=mtr
Reply With Quote
  #8  
Old 08-27-2012, 03:19 PM
fasteddiecopeman's Avatar
fasteddiecopeman fasteddiecopeman is offline
Member
 
Join Date: Jul 2008
Location: Kelowna, BC - summer; Florence, AZ - winter
Posts: 6,634
Default

Quote:
Originally Posted by Time View Post
...Should I pull the swing arm and grease the bearings while I'm at it? If it like the one in my KLR there wasn't enough grease to lube a ant's a$$ in all of them together....
Pulled my swingarm and greased the bearings at 13,800 kms. Everything HAD grease when I went in there, but not a lot extra.
__________________
Ed

My KLR trip to Alaska, YT, NWT and BC in summer 2009
http://www.klr650.net/forums/showthread.php?t=69383

My Versys trip to D2D 2013, and Alaska, June '13
http://www.kawasakiversys.com/forums...ad.php?t=33153
Reply With Quote
  #9  
Old 08-28-2012, 12:38 PM
Toddzilla's Avatar
Toddzilla Toddzilla is offline
Member
 
2008 Kawasaki Versys
Join Date: May 2010
Location: Cross Plains, WI
Posts: 188
Default

I found plugs at a local shop for $11 this weekend.

The real shocker was, I call the local Kaw dealer and was quoted $14 per valve shim.
They are a single piece of metal 3.05mm thick by 7.5mm in diameter. If you needed to re-shim every valve it would cost $120 just for the shims.

Local independant had them for $4 ea.
__________________
"Always go forward. Going straight is no fun."

'08 Red
Givi shield
Famsa Tank bag and pannier set
Happy Trails Panniers
Zeta blinker handgaurds
SeatPad Mod w/ Alaska leather cover
Heated grip wraps
Fiammi Hi & low tone horns

2008 V
1985 BMW R80
1989 Honda XR600R (650)
1980 Yamaha TT250
Reply With Quote
  #10  
Old 08-28-2012, 04:36 PM
fasteddiecopeman's Avatar
fasteddiecopeman fasteddiecopeman is offline
Member
 
Join Date: Jul 2008
Location: Kelowna, BC - summer; Florence, AZ - winter
Posts: 6,634
Default

Quote:
Originally Posted by Toddzilla View Post
I found plugs at a local shop for $11 this weekend.

The real shocker was, I call the local Kaw dealer and was quoted $14 per valve shim.
They are a single piece of metal 3.05mm thick by 7.5mm in diameter. If you needed to re-shim every valve it would cost $120 just for the shims.

Local independant had them for $4 ea.
After reading a post by "invader" where he works his shims down on emery cloth, I decided to try it (along with LOTS of others)....



It works like a DAMN! And - you end up with EXACTLY the clearances you need.



Try a "SEARCH" for it.
__________________
Ed

My KLR trip to Alaska, YT, NWT and BC in summer 2009
http://www.klr650.net/forums/showthread.php?t=69383

My Versys trip to D2D 2013, and Alaska, June '13
http://www.kawasakiversys.com/forums...ad.php?t=33153
Reply With Quote
  #11  
Old 08-28-2012, 05:42 PM
invader's Avatar
invader invader is offline
Member
 
Join Date: Mar 2008
Location: Kapuskasing Ontario Canada
Posts: 5,852
Default

I thinned and switched some shims around, to set all my inlet valves' clearances at 0.18 mm, and exhausts at 0.26 mm near middle of spec range. I used wet fine emery cloth on a flat wood surface to thin some of my original shims.

If you're not up to the task, you can get 7.48 mm diameter shims (same as Versys) in 0.025 mm increments (instead of only 0.050 mm increments) in 2.50 mm to 3.50 mm thicknesses.

Suzuki 2004-2005 RM-Z250 shims $8.47
Kawasaki 2006-2011 KX-250F shims $8.96
(Versys shims 0.050 mm increments $11.78)

Shim ------- Suzuki # ----- Kawasaki #

2.800mm - K9218-00179 - 92180-0179
2.825mm - K9218-00180 - 92180-0180
2.850mm - K9218-00181 - 92180-0181
2.875mm - K9218-00182 - 92180-0182
2.900mm - K9218-00183 - 92180-0183
2.925mm - K9218-00184 - 92180-0184
2.950mm - K9218-00185 - 92180-0185
2.975mm - K9218-00186 - 92180-0186
3.000mm - K9218-00187 - 92180-0187
3.025mm - K9218-00188 - 92180-0188
3.050mm - K9218-00189 - 92180-0189
3.075mm - K9218-00190 - 92180-0190
3.100mm - K9218-00191 - 92180-0191
Reply With Quote
  #12  
Old 08-29-2012, 08:41 AM
Toddzilla's Avatar
Toddzilla Toddzilla is offline
Member
 
2008 Kawasaki Versys
Join Date: May 2010
Location: Cross Plains, WI
Posts: 188
Default

I don't know. I'd rather have my shims sized then hardened.

Messing with hardened metal can have unforeseen consequences.

I certainly don't want one breaking up at 8,000 rpm's.
__________________
"Always go forward. Going straight is no fun."

'08 Red
Givi shield
Famsa Tank bag and pannier set
Happy Trails Panniers
Zeta blinker handgaurds
SeatPad Mod w/ Alaska leather cover
Heated grip wraps
Fiammi Hi & low tone horns

2008 V
1985 BMW R80
1989 Honda XR600R (650)
1980 Yamaha TT250
Reply With Quote
  #13  
Old 08-29-2012, 04:46 PM
fasteddiecopeman's Avatar
fasteddiecopeman fasteddiecopeman is offline
Member
 
Join Date: Jul 2008
Location: Kelowna, BC - summer; Florence, AZ - winter
Posts: 6,634
Default

Quote:
Originally Posted by Toddzilla View Post
I don't know. I'd rather have my shims sized then hardened.

Messing with hardened metal can have unforeseen consequences.

I certainly don't want one breaking up at 8,000 rpm's.
I BELIEVE that over-bucket shims (like on KLR650s) are hardened because they contact the cam lobes, but that under-bucket ones don't need to be. After 'doing' mine on emery cloth, I can say, pretty unequivocally, that they ain't hardened (or I'd STILL be working on them...!).

__________________
Ed

My KLR trip to Alaska, YT, NWT and BC in summer 2009
http://www.klr650.net/forums/showthread.php?t=69383

My Versys trip to D2D 2013, and Alaska, June '13
http://www.kawasakiversys.com/forums...ad.php?t=33153
Reply With Quote
  #14  
Old 08-29-2012, 06:43 PM
craigercj's Avatar
craigercj craigercj is offline
Member
 
Join Date: Jun 2011
Location: South Texas
Posts: 135
Default

I got the hot cams 7.48mm kit.
__________________
'09 Versys
'07 DRZ400SM
Past
'93 KX250
'82 IT175
'79 KE90
Reply With Quote
  #15  
Old 08-31-2012, 11:20 AM
Mursili's Avatar
Mursili Mursili is offline
Member
 
Join Date: Jul 2008
Location: Los Alamos, NM
Posts: 520
Default

Quote:
Originally Posted by Toddzilla View Post
I don't know. I'd rather have my shims sized then hardened.

Messing with hardened metal can have unforeseen consequences.

I certainly don't want one breaking up at 8,000 rpm's.
I would think that the harder they are, the more likely one would "break up." If they were too soft, then perhaps they would be "pounded flat."
__________________
When it comes to havoc, no one wreaks like me! - Dr. Heinz Doofenshmirtz

I will never be good and that's not bad. - Ban-Anon
Reply With Quote
  #16  
Old 08-31-2012, 11:50 AM
scooter650's Avatar
scooter650 scooter650 is offline
Member
 
2007 Kawasaki Versys
Join Date: Jul 2008
Location: western canada (Ab)
Posts: 225
Default

most shops will trade shims for ones in stock in the mechanics shim bins in the back...you just won't have any spares. the shims spin in/under the bucket so I wouldn't hand grind them... odds of getting them perfectly square surfaced by hand is slim to none imo.
Reply With Quote
  #17  
Old 11-20-2012, 10:28 AM
lgajohnymac lgajohnymac is offline
Member
 
Join Date: Mar 2009
Location: WNC
Posts: 176
Default

Quote:
Originally Posted by Squirreltoe View Post
I would not change plugs yet unless you are noticing problems. Mine looked really good yet at 15,000 miles. I didn't touch the filter until 15,000 either and I ride a fair amount of gravel. I posted some pics in another thread.


http://www.kawasakiversys.com/forums...ht=squirreltoe

Good Luck!
I also did a lot of dirt road riding on my 09. Every time I cleaned the filter I found sand and grit behind it. And I am also in the middle of troubleshooting a oil consumption problem now with 45k on the clock. I saw a thread somewhere in which a guy added pod filers behind the stock filter. In my case, I wish I had done that earlier, and I may do it now once I find root cause on my oil issue. Thread is here http://www.kawasakiversys.com/forums...ad.php?t=20885
__________________
09 Green
04 KTM EXC250
76 KE125
86 VF1000R
74 CB350F in process
Reply With Quote
  #18  
Old 11-23-2012, 04:56 AM
David RSparky3 David RSparky3 is offline
Member
 
Join Date: Aug 2011
Location: Northern New York
Posts: 265
Default

Looked at plugs @ 12000 miles put them back. Adjusted valves, cleaned air filter that did not need cleaning, matched the Throttle bodies. Good for another 12,000 miles maybe even 20,000.

I just change the oil and ride it!

David
Reply With Quote
  #19  
Old 11-23-2012, 12:42 PM
Mursili's Avatar
Mursili Mursili is offline
Member
 
Join Date: Jul 2008
Location: Los Alamos, NM
Posts: 520
Default

Quote:
Originally Posted by David RSparky3 View Post
... Adjusted valves, ...

I just change the oil and ride it!
How much did you have the adjust your valves?
__________________
When it comes to havoc, no one wreaks like me! - Dr. Heinz Doofenshmirtz

I will never be good and that's not bad. - Ban-Anon
Reply With Quote
Sponsored Links
Advertisement
 
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Advertisements
All times are GMT -5. The time now is 06:36 AM.


Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.

Motorcycle News, Videos and Reviews
Honda Grom Forum Harley Davidson Forum Honda 600RR Kawasaki Forum Yamaha R6 Forum Yamaha FZ-09 Forum
1199 Panigale Forum Roadglide Forum Honda CBR1000 Forum Vulcan Forum Yamaha R1 Forum Yamaha R3 Forum
Ducati Monster Forum Harley Forums Honda CBR250R Forum ZX10R Forum Star Raider Forum Yamaha Viking Forum
Suzuki GSXR Forum V-Rod Forums Honda Shadow Forum Kawasaki Motorcycle Forum Star Warrior Forum KTM Duke 390 Forum
SV650 Forum BMW S1000RR Forum Honda Fury Forum Kawasaki Versys Forum Drag Racing Forum Ducati 899 Panigale Forum
Suzuki V-Strom BMW K1600 Triumph Forum Victory Forums Sportbikes BMW NineT Forum
Volusia Forum BMW F800 Forum Triumph 675 Forum MV Agusta Forum HD Street Forum Suzuki GW250 Forum
Yamaha Motorcycles Victory Gunner Forum Honda Vultus Forum HD LiveWire Forum